What kind of nailer do i need

Essentially, this nailer would be used in delicate pieces where larger gauge nails might split the wood. Contractors are often split over whether brad or pin nailers are the best option for finishing work.

Brad nailers are also used for finishing, but they are compatible with larger nails — gauge. An gauge nail is still relatively small in the scheme of things, but still a fair bit larger than a pin nail. These nails also have more holding power. A brad nailer can be used in just about any application that requires a or gauge nail, such as:. A finish nailer can also be used for finish carpentry work, and they are designed to be used with specific sized nails.

A finish nailer differs from a brad or pin nailer in that it can handle larger and bulkier pieces of wood. These nailers are compatible with to gauge finish nails, which are a little bit bigger than a brad nail. Staple guns are nothing like any of the other nailers listed above, but can still drive staples a type of fastener into a wide range materials. Staple guns are highly versatile tools, and they can be used for a wide range of applications, including:.

While a staple gun cannot replace a power nailer in most projects, it does have its place and is a helpful tool to have in the home. Having a better understanding of the types of nailers available will make it easier to select the right one for the job.

Generally, the name of the nailer gives a good indication of the type of projects the tool can handle. Thank you very much! Now I know what kind I need due to this very informative article. Glad it helped and congrats on your new home! Have fun and enjoy the process of DIY. But, what types of nails do they drive? Are these collated nails, box nails? What length and diameter, for an 8d, 10d, and 16d?

Thanks so much, so informative, been meaning to get 1 to make a headboard, now i know which 1 to get and will use it for other DIY projects. Thank you for this very information, as I now have positive knowledge of what I should buy for my project. Good article! The thing I was looking for was an explanation of all the different angles that these things work at and why one is better for which particular job. Satisfied my questions about the different nail guns. Next, the different sizes of nails explained.

Gauge, penny, etc. Save my name, email, and website in this browser for the next time I comment. Framing Nailer Framing nailers are the heaviest duty nailer, and their name is fitting.

Wood sheathing. Wood siding. You'll have to experiment some, of course. Making sure the nails fully penetrate the backing board, but no more than necessary. Answer: Apart from the question being too vague, it depends on the type of materials and density. For thin plywood, 18 gauge would suffice. For heavier plywoods or hardwoods, 16 gauge would do the job.

You need to adjust the nailer air pressure for different densities so that the nail head ends up just below the surface. A nail every 6 inches is usually enough to hold a panel, as long as the nail is long enough to fully penetrate into a solid surface underneath, like a wall stud 2x4.

Answer: This depends on the type of studs or sub-surface you're attaching the planks to. Answer: You haven't mentioned what the sheets are being attached to. I'm assuming floor joists. In this case, you can use the product I mentioned in a previous answer above see the homedepot link.

Which nail gun would work best for both types of boards? Answer: A finishing nailer will work for all these types of boards, although the baseboard and trim may need longer nails, depending on the thickness. By the way, true 'shiplap' boards have a rabbet joint on each edge, so they overlap.

Whereas, plain wood planks or tongue and groove are not true shiplap boards. Question: I have 10mm oak flooring board which have lifted. I need to nail these boards firmly down into the solid concrete building slab, which is very tough. Answer: The issue of laying wood flooring on top of a concrete slab is a complex one. You should check with your local municipality for building codes, or hire a contractor that is knowledgeable in this type of installation.

It also depends whether the concrete is above or below grade. In general, however, it involves making sure the concrete is completely dry, then laying a 6-mil vapor barrier on top. Then laying plywood planks on top of this, using concrete screws to fasten the plywood to the slab. You can then install your flooring in the normal way. A flooring nailer is the best type to use.

They do come as electric nailers. Question: I own a porter cable nailer f Can I use three-inch finishing nails in my porter cable nailer?

Answer: I couldn't find a model f The nearest is a fr, which is a framing nailer. As such, the nails have larger, round heads.

Without seeing this model, I can't say whether it would accept finishing nails. I would imagine that the firing mechanism is sized to shoot large head nails, and it may jam if you tried using finishing nails, even if they fit in the magazine feed. You're on your own on this one.. I will not be held responsible or liable for any actions you take. Answer: The trouble with using a nailer with sheet metal is, except for roofing nails, the other types of nailer's nails have very small heads on them.

You need some flat headed nail to hold the metal to the wood beneath. Roofing nails would be too unsightly for siding repairs, and I've not found any nailer nails that are sort of 'in-between. If you haven't got too many repairs to make, you could go back to the old hammer and nails method. It's best to drill a small hole in the siding for each intended fix, before pounding a nail into it. This will prevent a big dimple in the siding where the nail punctures the metal.

Answer: If the red oak is flooring planks, then use a flooring nailer, otherwise, a finishing nailer and 1" nails should work fine. Answer: Yes, you can use a finishing nailer as long as it's not a brick wall you're nailing into. In that case, you should use concrete screws such as TapCon. Question: I'm planning on doing some fairly light framing for a travel trailer. What type of nailer do you recommend?

Answer: Assuming you don't want to see large nail heads, use a finishing nailer, with 3" ga. Answer: Not in my experience. Brick is much too dense to nail into directly. Even concrete nails would not hold very well, or very long. You need to drill holes with a concrete drill first, and use either plastic or metal anchors and appropriate sized screws. Or use Tapcon concrete screws. Answer: I wouldn't rely on the plaster being strong enough to hold any large piece of wood or trim, unless you locate the studs behind the plaster, and nail into that.

Question: I am building some cubby shelves from plywood. What type of nail gun should I use? Answer: A finishing nailer should do the job. The only problem you'll have is attaching each vertical piece to the shelf below.

I would recommend a nail at a 45 degree angle near the bottom of the front edge and bottom rear edge, since you probably won't be able to get the nailer inside the cubby spaces. Use a nail length that will almost completely penetrate the shelf below.. Answer: For the structural parts of the deck frame 2x8's , a framing nailer is the best type to use. However, the deck boards may hold to the joists a few years longer, if you use deck screws instead.

What kind of nailer and what size nails should be used to install 2x4 shelving that will eventually hold a brick collection? No, I'm not kidding. The shelves will fill a space of about 3 feet between the studs of an outbuilding. Thanks so much for your help. Not sure what a pin nailer is. A brad nailer is a lighter duty nailer, intended for upholstery and such.

For thinner plywood or panelling and baseboard, use a finishing nailer, and nails that are about 3 times as long as the total thickness of the plywood and baseboard.

What is the difference between a Pin nailer, Brad nailer, and a Finish nailer? Which is preferable to attach baseboard, and also plywood to 2x4 not covered by sheetrock? I'm assuming you've made sure the studs are all completely dried out and free of mold residue. A finishing nailer will do the job. You'll want to use heavier nails for the casing 16 gauge , although screws would be better here, as this allows some adjustment of shims to get the casing levelled. It's very important to get all the casing perfectly level on the face and edge, otherwise you won't get the door to hang properly.

Our home was stripped down to the studs. I am getting ready to install the interrior doors casing, trim, the whole 9 yards , what type of nailer do you recommend for this install? You're looking for a flooring nailer, which fires the nail at an angle, through the tongue of the flooring.. Hi i fit alot of solid and engineering wood flooring and wanted to invest in a good gas gun for secret nailing what would be best. We also carry a value brand, called Freeman, which is not quite as durable for everyday use, but is great for occasional woodworking projects around the home.

Thank you for the information it will help me in the near future casue i bought a house and it needs alot of work. I'm looking into getting an air nailer to do projects around the garage and maybe around the house. What kind of nailer should I get?

We usually recommend starting with an 18 gauge brad nailer, as it will give you the most versatility - whether you're working with larger wood trim, or smaller pieces of woodwork.

The ultimate choice really depends on what you're primarily planning to use the tool for. For small, intricate pieces of woodwork, a pin nailer may be more suitable. Hello would a 16 gauge 2. Reviews say you can do it but im not sure. It would depend how small the fencing is. If it's decorative wood fence with thin pieces of wood, a 16 gauge nailer would probably be sufficient.

If it's larger fencing, you'd need a fencing or framing nailer. I would think a 2. I could always drill screws for the posts. Thanks again. The project you're describing sounds like you're better off using a siding and fencing nailer, such as the Hitachi NV65AH2. Worst case, you should consider investing in a framing nailer, which would also be very capable. Thank you for sharing your experience and tips. I usually browse on the internet first to find out which tools that has the best roofing nailer price and quality.

So I really appreciate that you post this great information. Hey there! Would you mind if I share your blog with my facebook group? There's a lot of folks that I think would really enjoy your content. Please let me know. Cheers real madrid drakt. Love them. What Bostitch would be the right one? Hi, and thanks for your email. It's a degree framing nailer that drives plastic strip collated round head nails.

I am trying to repair my carport. What type of nail gun would I use to secure post to post. Hi Phyliss, Repairing a post like this requires a framing nailer. A great option is the Everwin FSN , an affordable tool with a degree-angle magazine.

Best of luck to you! Without knowing more about your project, it's hard to provide a recommendation. Please contact our customer service team for further information. You can email sales nailgundepot. I'm looking to purchasing a nail gun to put up ceiling plank over a popcorn ceiling. What type of nail gun is best suited for this particular project and can you recommend a good nail gun? Gary, It sounds like a 15 gauge finish nailer is going to be your safest bet, without knowing the thickness of the drywall.

Be sure to use wood glue when adhering the planks to your ceiling - in addition to nailing in place. As far as product recommendation, all of the tools we stock are intended for contractor-grade use. You can find our 15 Gauge Finish Nailers Here.

I am looking for a air nail gun to do wood siding. I want to use the smallest nail heads efficient enough to do the job. Do you have any suggestions on the gun and the size of nails to use. Are the nails in a coil?